DIY Concrete
-
Akona® Concrete & Mortar Color
Akona® Concrete & Mortar Colors give you a simple way to color your concrete, masonry, or grout project. Made of synthetic mineral oxide, these color additives will provide a durable, alkali– and ultraviolet-resistant finish to any cementitious application. Just add one canister to a bag of concrete, mortar, or grout mix to give your project a more decorative look. Great for use with TechMix® Premium Countertop Mix! Available in Charcoal, Terracotta, Brick Red, Buff, and Brown.
-
Quikrete® FastSet™ Repair Mortar
FastSet™ Repair Mortar demonstrates low sag, making it ideal for vertical or overhead repairs. FastSet™ Repair Mortar is also available with integral corrosion inhibitor in cases where maximum corrosion protection is desired. The addition of corrosion inhibitor has no adverse effect on the other physical properties of the product. This product can be built up […]
-
Quikrete® FastSet™ Water-Stop Cement
High Performance Cement FastSet™ Water-Stop Cement (BOM #113205) is a rapid setting, high strength repair material designed to plug leaks instantly in concrete and masonry. FastSet™ Water-Stop Cement will block running water when application is made to masonry or concrete surfaces. This special formulation allows the product to obtain high strength and rapid setting while repelling water. FastSet™ Water-Stop Cement solves leakage problems wherever active water is present, in all masonry and concrete above and below grade. Use FastSet™ Water-Stop Cement for sealing around concrete pipes and for plugging leaks in: • Foundation and retaining walls • Chimneys • Swimming pools, fountains and cisterns
-
Rapid Patch® Concrete Crack & Patch
Rapid Patch Concrete Crack & Patch is a heavy duty, fast-setting patching material for concrete block, sidewalks, patios, steps, and other concrete or masonry surfaces. This product is suitable for interior or exterior applications and may be trowel applied over existing concrete surfaces from a feather edge to a one half inch thickness to refinish the concrete surface.
-
Rapid Patch® FlexCrete
Rapid Patch FlexCrete is a single component, polymer modified, Portland Cement based waterproofing mortar for use in applications where a flexible, durable watertight barrier is required. Flexcrete is designed to bond to concrete and masonry surfaces, is resistant to freeze thaw conditions and chemical and sulfate exposure.
-
Rapid Patch® Hairline Crack Repair
Rapid Patch Hairline Crack Repair is a two-component, low-viscosity, 100% solids, urethane repair product designed for filling cracks in structural materials including concrete and bricks, for the purpose of bonding and sealing them. Product goes on black and dries gray. Designed for filling narrow cracks with maximum width of ¼ in. (6 mm) to a maximum depth of 6 in. (150 mm).
-
Rapid Patch® Rapid Loc™ Concrete & Veneer Bond
Rapid Patch® Rapid Loc™ Concrete & Veneer Bond is an innovative high-grab sealant which has high initial tack to hold materials in place while the adhesive cures, specifically designed for adhering stone, ceramic tile, and other construction materials to vertical surfaces. Rapid Loc Concrete & Veneer Bond is based on silyl-modified polymer technology that cures on exposure to atmospheric moisture to form a fast, tough, durable adhesive. Rapid Loc Concrete & Veneer Bond exhibits excellent adhesive properties to most common substrates including stone, brick veneer, aluminum, brass, vinyl, steel, stainless steel, glass, mirrors, mortar, concrete, wood, OSB, plywood, ceramic tile, brick, foam board, pavers, painted surfaces, fiberglass, and many plastics. Rapid Loc Concrete & Veneer Bond is highly weather resistant, remains flexible in low temperature extremes, and can be painted with most paints. Available in 9.5 oz. tube (BOM #130170).
-
Sakrete® 5000 Plus High Strength Concrete Mix
Sakrete® 5000 Plus Concrete Mix (BOM #120020) is a professional grade concrete mix used for building and repairs greater than 2" depth.
-
Sakrete® Epoxy Tube Nozzles (3-Pack)
Sakrete® Epoxy Tube Nozzles are intended to provide customers additional nozzles for use with epoxy tube products. Both the original nozzle and the replacements are one-time use nozzles which should be discarded after use. This solves the issue when customers use only a portion of the product, but have to discard of the original one-time use nozzle. This product comes in packs of 3 tubes per bag.
-
Quikrete® 5000 Concrete Mix
Quikrete® 5000 Concrete Mix (BOM #104624) is a commercial-grade blend of stone or gravel, sand and cement specially designed for higher early strength and ideal for cold weather application. Just add water, mix and use for concrete projects 2" thick or more such as driveway aprons, patios, deck supports, and sign footings. Achieves 5,000 psi after 28 days.
-
Rapid Patch® Concrete Repair Mortar
Rapid Patch® Concrete Repair Mortar (20 lb. BOM #129460, 50 lb. BOM#129470) is a fast-setting, high-performance, multi-use blend of hydraulic cement, polymers, fine aggregates, and special additives used for concrete repair and new construction where high early strength, excellent durability, and low shrinkage is required. Mix with water for applications from ½ in. minimum to 6 in. maximum thickness (1.3-15 cm).
-
TechMix® Premium Concrete Countertop Mix
TechMix® Premium Concrete Countertop Mix is a fast-setting, high-strength mix specially formulated to create countertops, outdoor kitchen tops, bar or table tops, workbench or utility tops. This product can also be used to produce precast wall caps, mantel or lintels for many different applications. Premium Concrete Countertop Mix needs only water to produce an easy-to-use, pourable mixture that can be de-molded in 18-24 hours. Available in a 50 lb. bag in gray (BOM #103434) or white (BOM #104082).
-
Akona® Concrete/Masonry Set Accelerator
Akona® Concrete/Masonry Set Accelerator (BOM #103963) is an ASTM C494, Type C, non-chloride, non-corrosive, liquid that improves workability and initial strength while it reduces the hydration time of cement. The product is recommended for use during cooler weather to accelerate set time and reduce the risk of frozen mortar and concrete mixes. It is also recommended for use when early strength gain is desired to speed up projects. Akona Concrete/Masonry Set Accelerator provides a reduced curing time, faster set time and increased early strength. The product speeds finishing operations in any weather condition without any corrosive effects.
-
Quikrete® Color Additive
Quikrete® Color Additive is a liquid coloring agent used to customize the color of your concrete project. Mix with water and then add to dry concrete mix. One bottle will mix with two 80 lb. or 60 lb. bags of Concrete Mix. Available in Red (BOM #105510), Brown (BOM #105508), Buff (BOM #105509), Charcoal (BOM #105507), and Terra Cotta (BOM #107832).
-
TechMix® Concrete Mix
TechMix® Concrete Mix is a high strength pre-blended Portland cement mixture for pouring concrete 2 inches thick or greater. Used for general building and repairing steps, slabs, walks, and floors. Available in 60# bags (BOM #104879), 80# bags (BOM #104883) and 3,000# bags (BOM #112228).
-
Akona® Crack-Resistant Surface Bonding Cement
Akona® Crack-Resistant Surface Bonding Cement is a specially-formulated, multi-use product. It can be used to build and restore retaining walls or block walls, patch large vertical holes where non-sagging cement is a must, or repair deteriorated stucco. Because it contains special fibers it will not shrink, crack, or sag on a vertical repair. It also provides additional overall strength over conventional concrete. Available in Gray (BOM #102614).
-
Quikrete® Re-Cap Concrete Resurfacer
Quikrete® Re-Cap™ Concrete Resurfacer (BOM #112421) is a special blend of portland cement, sand, polymer modifiers and other additives. Designed to provide a shrinkage compensated repair material for making thin repairs to sound concrete in need of surface renewal. Can be squeegee, trowel or brush applied.
-
SAKRETE® Cement Mix Accelerator
Sakrete® Cement Mix Accelerator (BOM#120408) is a calcium-chloride based product designed to accelerate the set time of concrete, mortar, or any Portland cement based product.
-
Akona® Fast-Setting Anchoring Epoxy
Akona® Fast-Setting Anchoring Epoxy (BOM #120438) is a two-component, high-performance, 100% solids, high-modulus, non-sag gel epoxy designed for anchoring bolts, railings, dowels, and rebar steel into concrete and to bond or repair a variety of household and common building materials including concrete, porous tile, and stone. Special no-mess, self-mixing tube for easier application. Non-shrink, resistant to chemicals and solvents, this high-strength, fast-setting epoxy has a gel time in as little as 12-14 minutes; initial cure of 2 hours; and final cure time of 12-16 hours. Use both horizontal and vertical, up to 1/8" (3 mm) annular width and 10" (254 mm) depth. Because it is moisture tolerant, it is ideal for stopping air and water leaks. Gray in color.
-
Quikrete® Crack-Resistant Concrete Mix
Quikrete® Crack-Resistant Concrete Mix (BOM #109358) is a construction grade blend of Portland cement, sand, gravel & special reinforcing fibers to reduce shrinkage cracks and improve impact resistance. Just add water and mix to create for walkways, patios, steps, garage or shed floors.
-
Sakrete® Concrete & Asphalt Cleaner
Sakrete® Concrete & Asphalt Cleaner (BOM #120042) is a mild, acidic liquid used to clean concrete, masonry, and asphalt surfaces. Use to clean existing surfaces prior to making repairs.
-
Akona® Foundation Coating Cement
Akona® Foundation Coating Cement (BOM #102621) is a specially-formulated, cement-based product for coating and protecting polystyrene insulation board or insulated concrete forms (ICF) from weathering, ultraviolet rays, and general wear/impact. Akona Foundation Coating Cement is polymer-modified and contains fibers which reduces shrinkage and improves the adhesion properties of the product. Akona Foundation Coating Cement is easy to apply by masonry brush or trowel and has the superior durability of a Portland cement-based product. It also provides a tough, durable gray textured or stucco-like finish. If desired, the product may be integrally colored with a liquid cement or mortar colorant, or it can be painted to match existing home design.
-
Sakrete® Concrete Bonder & Fortifier
Sakrete® Concrete Bonder & Fortifier (BOM #120036) is a high-solids acrylic liquid bonding agent, used as a bonding admix or bonding agent enhance strength, durability, adhesion, abrasion resistance, and freeze-thaw resistance of concrete.
-
Quikrete® FastSet™ Repair Mortar
Quikrete® FastSet Repair Mortar (BOM #109719) is specifically formulated to make structural repairs to any concrete, masonry or stucco surface. This low-sag formula has a 20-30 minute working time which allows for sculpting of the material during placement and makes it ideal for vertical and overhead repairs. Just add water, mix, and use to repair concrete, masonry, or stucco surfaces. Exceeds ASTM C 928 R-2. Compressive strength ASTM C109 modified: 3 hours=2,000 psi, 24 hours = 4,000 psi, 7 days = 5,000 psi, and 28 days = 6,000 psi.
-
Akona® Instant Patching Cement
Akona® Instant Patching Cement (BOM #102632) is a high-performance cement used for filling wide cracks and other concrete repair needs. It sets rock hard in just 90 minutes. Akona Instant Patching Cement self-bonds to all properly-prepared concrete surfaces and develops twice the strength of ordinary concrete.
-
Quikrete® Fast-Setting Concrete Mix
Quikrete® Fast-Setting Concrete Mix (BOM #100166) is a special blend of fast-setting cements, sand and gravel designed to set hard in approx. 20 to 40 minutes. Sets posts without mixing. Pour dry mix into hole and soak with water. Use for setting fence posts, mailbox posts, basketball posts, deck posts, or lamp posts. Or use to construct new steps, sidewalks, or concrete appliance pads.
-
Akona® Instant Post Cement
Akona® Instant Post Cement (BOM #102631) is used for quick setting of all metal, wood and plastic fence, mailbox, basketball and swing set posts. This product does not require pre-mixing prior to use. Simply pour dry mix into the hole with water as directed. Instant Post Cement does not require bracing and sets in approximately 10-20 minutes. Akona Instant Post Cement is not designed to be used for footings or structural supports.
-
SAKRETE® Concrete Repair
Sakrete® Concrete Repair Tube (BOM#121099) is a weather-resistant, latex-based polymer used for filling cracks in concrete.
-
Sakrete® Crack Resistant Concrete Mix
Formulated to reduce the risk of surface shrinkage cracks, Sakrete Crack Resistant Concrete Mix is a professional strength blend of cementitious materials, sands, stone and fibers. For repair and building jobs where concrete thickness exceeds 2”.
-
Sakrete® Fast-Setting Concrete Mix
Sakrete® Fast-Setting Concrete Mix (BOM #120019 = 50 lb. pail / #106576 = 50 lb. bag) sets posts and poles quickly and easily, even without blending the material. Sets in just ½ an hour so that no bracing is needed and exceeds the strength requirements of ASTM C 387. Fast-Setting Concrete Mix is intended for applications requiring at least 2 inches in thickness.
-
TechPro® Heavy-Duty Stone Veneer Mortar
TechPro® Heavy-Duty Stone Veneer Mortar (BOM #120444) is a high-yield, lightweight, high-performance, polymer-modified, fiber-reinforced, Portland-cement based mortar for adhered installation of masonry veneer stone and natural stone. 25% lighter than traditional mortars with excellent non-sag and non-slump handling characteristics. Special admixtures help create both a mechanical and chemical bond to the substrate, significantly outperforming standard mortars. TechPro Heavy-Duty Stone Veneer Mortar is "Step 2" of the TechPro stone installation system used to create decorative exterior and non-load bearing interior veneer walls.
-
Sakrete® Form Release Oil
Sakrete® Form Release Oil (BOM #120044) is a release agent for use with concrete forms. Allows forms to be removed earlier and easier, yet has only a light residue.
-
Tenon® Instant Anchoring Cement
Tenon® Instant Anchoring Cement is a quick-setting, anchoring cement compound used for setting poles, railings, bolts, and fixtures in concrete or masonry. Suitable for interior or exterior use. Expands as it hardens to set securely and lock in place for strong support. Any metals that will corrode when exposed to wet cement, such as aluminum, must be protected. Available in 10 lb. (BOM #129940) and 50 lb. pails (BOM #120998).
-
Sakrete® High Strength Concrete Mix
Sakrete® High Strength Concrete Mix (BOM #100171 = 60 lb. bag / #120021 = 50 lb. pail / #101090 = 80 lb. bag) is designed for anchoring posts and poles, and pouring footings and slabs. High Strength Concrete Mix is premium quality for consistent strength and durability and meets ASTM C 387 strength requirements for structural applications. Uses include building walks, drives, slabs and steps as well as anchoring posts and poles. High Strength Concrete Mix is for applications requiring at least 2 inches in thickness. Just add water, mix, and use.
-
TechPro® Moisture Barrier
TechPro® Moisture Barrier (BOM #127610) is an advanced, latex, polymer-based technology used as a water-resistant membrane applied to all wood or moisture-sensitive backup walls prior to application of TechPro Polymer-Modified Stone Veneer Base Coat. Ready to use (no mixing required), with exceptional flexibility and elongation, solvent free and VOC compliant, TechPro Moisture Barrier is part of the TechPro veneer stone installation system. Color will be light orange when applied, dries to dark orange.
-
Sakrete® Sand Mix
Sakrete® Sand Mix (BOM #100397) is a quality mixture of sand and cement designed to be used as a topping mix to rejuvenate damaged concrete surfaces or as a bedding mix and joint grout for flagstone, slate, and brick walkways. Sand Mix can be applied in layers ranging from ½ to 2 inches thick and exceeds the strength requirements of ASTM C 387. Just add water, mix, and use.
-
Akona® Epoxy Tube Nozzles (2-Pack)
Akona® Epoxy Tube Nozzles are intended to provide customers additional nozzles for use with epoxy tube products. Both the original nozzle and the replacements are one-time use nozzles which should be discarded after use. This solves the issue when customers use only a portion of the product, but have to discard of the original one-time use nozzle. This product comes in packs of 2 tubes per bag.
-
TechPro® Stone Veneer Joint Grout
TechPro® Stone Veneer Joint Grout is a mixture of dry cementitious materials and dried sand designed to fill joints between real or manufactured stone veneer units. Preblended with air-entrainment admixtures to resist freeze-thaw conditions while increasing flow and durability. Specially formulated for clean installation and flow properties to eliminate clogging when using a grout bag. Mix with water only. "Step 3" of the TechPro stone veneer installation system used to create decorative exterior or non-load bearing interior veneer walls. Available in 4 colors to compliment or contrast veneer units: Gray (BOM #120446); Brown (BOM #120449); Tan (BOM #120448), White (BOM #120447); and Charcoal (BOM #130110).