Tenon^®

Tenon^® 100% Silane Sealer

Tenon® 100% Silane Sealer is a clear, solvent-based, concrete sealer that penetrates deep into, and reacts chemically, within the capillaries of the concrete or masonry in order to protect against moisture penetration and the spalling, freeze damage, and  rebar corrosion which moisture can cause. It is suitable for use to protect and seal fully-cured fresh concrete, cast in place, precast, and high strength concrete materials. 100% Silane Sealer is used for above-grade exterior applications that are not subject to hydrostatic pressure. It is excellent for treating high traffic areas or surfaces that receive high salt concentrations such as coastal piers.  Available in 1 gal. bottle (BOM #129890), 5 gal. pail (BOM #129900) and 55 gal. drum (BOM #129652). 

Tenon^® 20% Silane Sealer

Tenon® 20% Silane Sealer is a clear, solvent-based concrete sealer that penetrates deep into and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and  rebar corrosion which moisture can cause. It is suitable for use to protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. Silane sealers are used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129980), 5 gal. pail (BOM #129970) and 55 gal. drum (BOM #129644). 

Tenon^® 40% Silane Sealer

Tenon® 40% Silane Sealer is a clear, solvent-based concrete sealer that penetrates deep into and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and  rebar corrosion which moisture can cause. It is suitable for use to protect, and seal fully-cured fresh concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. 40% Silane Sealer is used for above-grade exterior applications that are not subject to hydrostatic pressure.  Available in 1 gal. bottle (BOM #129870), 5 gal. pail (BOM #129860) and 55 gal. drum (BOM #129597). 

Tenon^® 40% Silane Sealer WB

Tenon® 40% Silane Sealer WB is a VOC compliant, clear, non-yellowing, concrete sealer that penetrates deeply and reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and spalling, freeze damage, and rebar corrosion due to moisture interaction. It is suitable for use to protect, and seal fully cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials. Tenon® 40% Silane Sealer WB is designed for use above-grade exterior applications that are not subjected to hydrostatic pressure. Available in 1 gal. bottle (BOM #114417), 5 gal. pail (BOM #114427) and 55 gal. drum (BOM #114415). 

Tenon^® Adhesive Base Coat PM

Tenon® Adhesive Base Coat PM (BOM# 114899) is a dry-mix, polymer-modified adhesive and base coat requiring only water for mixing.

Tenon^® Air-Entrained Concrete Patching Mix AE

Tenon® Air-Entrained Concrete Patching Mix AE (3U58M) (BOM #126199) is an ideal material for repairing concrete pavement, bridge decks, industrial floors, concrete parking lots, and garage decks. This pre-blended mixture of cement, aggregate, and special additives will produce a high strength concrete repair material that is extremely durable and works well in harsh environments. Additionally, when used with Tenon Fast-Set Liquid Activator, surfaces can be reopened to traffic within 4 to 5 hours under typical conditions.

Tenon^® Air Entrainment

Tenon® Air Entrainment (BOM #120377) is a ready-to-use, aqueous solution made of organic materials.  Air Entrainment entrains a small and stable amount of air into the desired mix. These small, stable air voids enhance the mixture and improve workability. Its chemical composition and physical properties make it ideal for many construction applications. It is intended for use when increased workability and freeze-thaw durability of concrete or mortar is preferred. This admixture also improves resistance to freeze/thaw, scaling, segregation, and bleeding and improves strength, plasticity, water retention, and cohesiveness of mortar. Meets ASTM C260 Standard Specification for Air-Entraining Admixtures for Concrete.

Tenon^® Blend-Pro^™

Tenon® Blend-Pro™ is a fast-setting, one component, polymer-modified, calcium aluminate cement-based concrete and masonry patching compound designed for vertical and overhead repair applications.
Available in #3-15 Light Gray (BOM# 113529, 121158), #3-30 Light Gray (BOM# 113532, 114797).

Tenon^® Burnished Block Sealer

Tenon® Burnished Block Sealer is used as a final sealer on masonry block walls including burnish block or ground face block, architectural block, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Burnished Block Sealer enhances the beauty, giving the surface a rich “wet-look” sheen. It forms a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Made with a blend of methacrylate polymers, this aromatic solvent-based coating does not yellow when exposed to the sun’s UV rays. Available in 1 gal. bottle (BOM #121100), 5 gal. pail (BOM #129530), and 55 gal. drum (BOM #121101).

Tenon^® Burnished Block Sealer WB

Tenon® Burnished Block Sealer WB is used as a final sealer on masonry block walls including burnish block or groundface block, architectural block, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Burnished Block Sealer WB enhances the beauty, giving the surface a rich “wet-look” sheen. It forms a breathable membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Made with an acrylic that does not yellow when exposed to the sun's UV rays. Available in 1 gal. bottle (BOM#121110), 5 gal. pail (BOM#121107), and 55 gal. drum (BOM#121113).

Tenon^® Burnished Block Sealer WB Matte

Tenon®Burnished Block Sealer WB Matte is used as a final sealer on masonry block walls including burnish block or groundface block, architectural block, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. It enhances the beauty, giving the surface a rich "wet-look" without the gloss. It forms a breathable membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Made with a durable polysiloxane that does not yellow when exposed to the sun's UV rays. Available in a 1 gal. bottle (BOM #130090), 5 gal. pail (BOM #130080) and 55 gal. drum (BOM #129695).

Tenon^® Commercial DOT Repair

Tenon® Commercial DOT Repair is a rapid-setting, high-strength, polymer-modified, one-component hydraulic cement mortar designed for concrete repair and overlay applications requiring high durability. Meets or exceeds ASTM C928-R3 Standard Specification for Packaged, Dry, Very Rapid, Hardening Cementitious Materials for Concrete Repair. Resistant to salts, grease, oil, and other chemicals often found in the transportation environment. Commercial DOT Repair is approved by MNDOT for "Rapid Hardening Materials for Repairs" and WYDOT for "Bridge Concrete Repair". Available in 50 lb. bags "Neat" (BOM # 100689), and "Extended" (BOM #110735).

Tenon^® Concrete & Masonry Dissolver

Tenon® Concrete & Masonry Dissolver is an environmentally-friendly liquid alternative to aggressive acid concrete removers. Use to safely dissolve and remove cured concrete, mortar, grout, and stucco build-up from tools, concrete forms, job mixers, hardware, shoring, and more.

Tenon^® Concrete & Masonry Sealer WB

Tenon® Concrete & Masonry Sealer WB is a water-based sealer that penetrates and reacts chemically within the capillaries of the concrete or masonry, bonding to the silica in the substrate to protect against moisture penetration, water-related staining, atmospheric chemicals, and deterioration. It is used to protect and seal clean, dry, coating-free, fully-cured concrete, brick masonry, concrete masonry units, stucco, stone terrazzo, architectural concrete, and some natural stones. For above-grade exterior applications that are not subject to hydrostatic pressure. Ready-to-use, this low VOC, silane/siloxane emulsion is especially suited for applications where VOC regulations for AIM coatings prevent the use of solvent-borne products. Available in 1 gallon bottles (BOM #120673) and 5 gallon pails (BOM #120674).

Tenon^® Concrete & Mortar Dissolver RM

Tenon® Concrete & Mortar Dissolver RM is an environmentally-friendly liquid alternative to aggressive acid based concrete removers. Concrete & Mortar Dissolver RM is specifically designed for use in the ready-mix industry to clean equipment while the concrete and mortar are still in their plastic state. This product will retard the set time and prevent the cementitious bonds from forming, allowing the material to be easily washed from the equipment and tools.

Tenon^® Concrete Patching Mix

Tenon® Concrete Patching Mix (BOM #126198) is a dry mixed combination of Portland-limestone Cement and aggregates that is proportioned and manufactured according to MnDOT specification 3105 for grade 3U18. When mixed according to specifications with water and admixtures, it is an ideal mixture for repairing concrete pavement, industrial floors, and structural concrete.

Tenon^® Concrete Resurfacer

Tenon® Concrete Resurfacer (BOM #120728) is a fast-setting, high-performance polymer-modified, cement-based product used for resurfacing old concrete to make it look new again. Applications from feather edge to ½ in. (2-13 mm). Fast-drying, walkable on average in 2 hours.

Tenon^® Concrete Surface Retarder

Tenon® Concrete Surface Retarder is a water-based, “Formula S’’ mixture that is applied to freshly placed concrete applications to chemically delay the setting of the mortar at the surface of the concrete. This allows the top layer of cement paste to be flushed away creating an exposed aggregate decorative finish without damaging the integrity of the concrete slab. A stream of water or scrubbing with a stiff brush is used to create the decorative texture. Surface Retarder can also be used on concrete to roughen or open the surface to improve the bonding for coatings or toppings. Available in 1 gallon bottles (BOM #121117) and 5 gallon pails (BOM #121118).

Tenon^® Construction Grout

Tenon® Construction Grout is a non-shrink, non-metallic, Portland-limestone cement-based mixture of hydraulic cement, aggregate, and additives for general purpose structural grouting. Meets or exceeds ASTM C-1107. Available in 50 lb. bags (BOM #120720) and 3000 lb. bags (BOM #113219).

Tenon^® Critical Pavement Repair (CPR)

Tenon® Critical Pavement Repair (CPR) is a preblended, single-component, repair mortar designed to be a quick, durable repair for essential heavy-duty surfaces. This includes airport runways, concrete highways, parking structures, freezer rooms, loading docks, industrial floors, and much more. It is fast-setting, high-strength, polymer-modified, and fiber reinforced as well as freeze-thaw durable. CPR contains corrosion inhibitors to mitigate corrosion issues. It can be trowel applied on horizontal or vertical surfaces or pumped into place for formed vertical and overhead repairs. Meets ASTM C928 Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs. Available in a 50 lb. bag (BOM #113091).

Tenon^® Cure & Harden

Tenon® Cure & Harden is a clear, water-based silicate-based curing, hardening, and dustproofing concrete sealer. Tenon® Cure & Harden penetrates into and reacts chemically within the capillaries of the concrete or masonry surfaces. It is suitable for use on freshly placed and finished concrete and in the renovation of aged concrete.

Tenon^® Cure & Seal

Tenon® Cure & Seal is a non-yellowing, fast-drying acrylic compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete. Enhances colors, darkens the appearance of concrete, brick, stone, terrazzo, and exposed aggregate. Available in 1 gal. bottle (BOM #120839), 5 gal. pail (BOM #120838), or 55 gal. drum (BOM #120932).

Tenon^® Cure & Seal ES

Tenon® Cure & Seal ES is a clear, non-yellowing, fast drying acrylic compound.  No Fillers, oils, waxes, or saponifiable resins are contained in the mixture.  It is used for curing and sealing of freshly-placed and /or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials.  Cure & Seal ES forms a membrane film on new concrete to seal and retain hydrations water, providing maximum hardness of the substrate, resistance to abrasion, and resistance to damage caused by salt, oil, grease, mild acids, alkali, and stains from soot, smog, fumes, and gases.  Cure & Seal ES will also benefit existing concrete by penetrating into the slab, binding together the small dusting particles, while filling the voids to produce a non-porous, dust-free, brighter surface.   When used on terrazzo, brick, stone, and architectural concrete, it brings out the highlights, enriches, and enhances the natural colors found in the material.

Tenon^® Cure & Seal WB

Tenon® Cure & Seal WB is a clear, non-yellowing, acrylic polymer membrane forming compound used for curing, sealing, and hardening of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Waterborne mixture passes VOC compliance laws. Available in 1 gal. bottle (BOM #120823), 5 gal. pail (BOM #120822), and 55 gal. drum (BOM #120824).

Tenon^® Cure & Seal WB 1315

Tenon® Cure & Seal WB 1315 is a film-forming compound that meets ASTM C1315 performance standards for water loss when applied properly to cure, seal, and harden freshly placed concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Cure & Seal WB 1315 will pass all VOC compliance laws and is formulated to cure, seal, protect, and dustproof concrete, as well as seal many types of porous tile and resilient floors. Designed for both exterior and interior applications, it is particularly recommended for indoor work in public buildings (hospitals, restaurants) and private residences where solvent-based systems are difficult to use. The white solution dries clear and provides a dust-free surface. This product provides maximum hardness to the concrete as well as resistance to traffic abrasion. Construction debris are easier to clean. Compatible with most tile and carpet adhesives.  Available in 1 gal. bottle (BOM #129910), 5 gal. pail (BOM #129920), and 55 gal. drum (BOM #129930).

Tenon^® Dissipating Cure 1315 WB

Tenon® Dissipating Cure 1315 WB is a water-based, clear resin, liquid membrane forming, curing compound used for moisture retention of freshly placed concrete. Tenon® Dissipating Cure 1315 WB is formulated for curing concrete. Designed for interior or exterior applications where a dissipating or easily removed curing compound is required. It is particularly recommended applications where greater moisture retention is required . Tenon® Dissipating Cure 1315 WB will pass all VOC compliance laws. Available in 5 gallon pails (BOM #113839), 55 gallon drums (BOM #113839), and 275 gallon totes (BOM #113838).

Tenon^® Dissipating Cure WB +PLUS

Tenon® Dissipating Cure WB +PLUS is a water-based, clear resin, liquid membrane forming, curing compound with silane used for moisture retention of freshly placed concrete. Designed for interior or exterior applications where a dissipating or easily removed curing compound is required. It is particularly recommended for applications where greater moisture retention is required . Tenon® Dissipating Cure WB +PLUS will pass all VOC compliance laws.

Tenon® Dissipating Cure WB +PLUS is available in 1 gal. bottle (BOM #114437), 5 gal. pail (BOM #114447), 55 gal. drum (BOM #114457), 275 gal. tote (BOM #114467) .

Tenon^® Fast-Set Liquid Activator

Tenon® Fast-Set Liquid Activator is formulated specifically to be used in conjunction with Tenon® Air-Entrained Concrete Patching Mix AE in order to establish a quicker set and develop strength rapidly. When used with the patching mix, Fast-Set Liquid Activator reduces the closure time of high-traffic areas from 24 hours to 4-5 hours under normal conditions. Available in 1 gallon bottles (BOM #120593) and 5 gallon pails (BOM # 120770).

Tenon^® Feather Edge Pro

Tenon® Feather Edge Pro (BOM #120540) is a trowelable, rapid-setting, polymer-modified, self-drying, Portland cement-based patch and skim coating compound for multiple interior substrates. Specially formulated with superior workability for easy application, this non-sanded product results in an ultra-smooth finish and can be applied from feather-edge to ½ in. (13 mm) and is ideal for use as an embossing leveler. Fast-setting, with initial set in 15 minutes; can accept ceramic tile and stone applications, as well as moisture-sensitive floor coverings, in as little as 30 minutes or when completely dry.

Tenon^® Feather Patch Pro

Tenon^® Feather Patch Pro is a fast-setting, polymer-modified, self-drying, cement-based patch and skim coating compound for interior use under ceramic tile, hardwood flooring, carpet and a wide array of floor coverings. Ideal for deeper patching, this product can be applied from feather-edge to 2 in. (51 mm) thick. Formulated for exceptional bond strength and superior workability, can be applied to concrete with a relative humidity (RH) up to 90%. Rapid-setting, with initial set in 15 minutes; can accept ceramic tile and stone applications, as well as moisture-sensitive floor coverings, in as little as 30 minutes or when completely dry. Available in 10 lb. (4.5 kg) pails (BOM #120618), and 25 lb. (11.3 kg) pails (BOM #120541).

Tenon^® FormGuard

Tenon® FormGuard is a V.O.C. compliant, ready-to-use, petroleum based, chemically reactive liquid concrete form release agent. Tenon FormGuard effectively prevents bonding of concrete to forms and formliners. Use of Tenon FormGuard regularly will increase the life of all forms. Tenon FormGuard can be used on forms such as steel, aluminum, fiberglass-reinforced, all grades of plywood, epoxy-coated, and urethane-coated.

Tenon^® FormGuard Citrus

Tenon® FormGuard Citrus is a V.O.C. compliant, ready-to-use, petroleum based, chemically reactive liquid concrete form release agent. Tenon® FormGuard Citrus effectively prevents bonding of concrete to forms and form liners. Use of Tenon® FormGuard Citrus regularly will increase the life of all forms. Tenon® FormGuard Citrus can be used on forms such as steel, aluminum, fiberglass-reinforced, all grades of plywood, epoxy-coated, and urethane-coated.

Tenon^® Hardener LS

Tenon® Hardener LS is a clear, water-based Lithium Silicate-based hardening, and dustproofing concrete sealer.  Tenon® Hardener LS deeply penetrates into the concrete surface and reacts chemically within the capillaries of the concrete surfaces.  The reaction forms a dense calcium silicate hydrate crystalline structure, providing a hard durable surface. It is suitable for use on recently finished concrete and in the renovation of aged concrete greater than 10 days old.

Tenon^® High Strength Precision Grout

Tenon® High Strength Precision Grout (BOM #120707) is a ready-to-use, high-strength, flowable precision grout mix with excellent working time and early strength ensuring quick job startups and reducing cost. This specially-formulated mix can be pumped into areas inaccessible by conventional grouting methods. High Strength Precision Grout is a non-shrink, non-metallic, non-staining, non-porous, high-density, pumpable formula designed for precision grouting applications and can be extended with the proper aggregates up to 50%.

• Highly-fluid grout with excellent working time and early strength
• Non-shrink, non-corrosive, non-staining, non-porous, and non-metallic
• Applicable Standards: ASTM C-1107 and CRD-C 621

Tenon^® Instant Anchoring Cement

Tenon® Instant Anchoring Cement is a quick-setting, anchoring cement compound used for setting poles, railings, bolts, and fixtures in concrete or masonry. Suitable for interior or exterior use. Expands as it hardens to set securely and lock in place for strong support. Any metals that will corrode when exposed to wet cement, such as aluminum, must be protected.   Available in 10 lb. (BOM #129940) and 50 lb. pails (BOM #120998).  

Tenon^® Instant Hydraulic Cement

Tenon® Instant Hydraulic Cement is a quick-setting hydraulic cement compound used primarily as a water stop or hole filler. It expands when set and locks into place to block flowing water in 3 to 5 minutes. For use only on concrete and masonry materials. Best for repairing leaks in cracks between blocks or on one surface, not for stopping water flow in corners.  Available in 10 lb. (BOM #129950) and 50 lb. (BOM #128280) pails. 

Tenon^® Level-Flo^® 100

Tenon® Level-Flo^® 100 (BOM #120534) is a Portland cement-based, self-leveling underlayment used to level and smooth interior floors for finished floor covering installation. Can be applied from ⅛"-2" (3-51 mm) neat and up to 5" (127 mm) extended.. Accepts non-moisture sensitive tile and stone in as little as 24 hours, and moisture sensitive floor coverings in 3 days. Use with Level-Flo Primer Pro to level and smooth over many interior substrates including concrete, existing ceramic tile, non-water soluble adhesive residue, and solid wood floors.

Tenon^® Level-Flo^® 200

Tenon® Level-Flo^® 200 (BOM #120535) is a high-performance, fiber-reinforced, non-gypsum based, self-leveling underlayment that provides a flat, extremely smooth, durable surface for finished floor covering installation. Can be applied from ⅛"-2" (3-51mm) neat, and up to 5" (127 mm) extended. Fast-setting, accepts non-moisture sensitive tile and stone in as little as 4 hours, and moisture sensitive floor coverings in 16-24 hours. Use with Level-Flo Primer Pro to level and smooth over many interior substrates including concrete, existing ceramic tile, non-water soluble adhesive residue, and solid wood floors.

Tenon^® Level-Flo^® 300

Tenon® Level-Flo^® 300 (BOM #120536) is a high-performance, high-strength, fiber-reinforced, non-gypsum based, self-leveling underlayment that provides a flat, extremely smooth, durable surface for finished floor covering installation. It’s designed for maximum flow and seamless merging with every pour and is ideal for fast track applications.

Tenon^® Level-Flo^® Primer Pro

Tenon® Level-Flo Primer Pro (1 gal. BOM #129436, 5 gal. BOM #129438) is a high quality, acrylic latex based primer used with Tenon® Level-Flo self-leveling products. Level-Flo Primer Pro is applied to porous and nonporous surfaces as a substrate primer to promote bonding. This primer can also be used with other cement-based Tenon concrete repair, surface preparation, and polymer-modified thin set mortars to enhance bonding to difficult substrates such as glazed ceramic tile, terrazzo, gypsum based underlayments, concrete treated with certain types of curing compounds (acrylic resin or silicate curing compounds only), well bonded epoxy coatings, and cold rolled steel. Tenon Level-Flo Primer or Primer Pro are required to be applied to all substrates before placing Tenon® Level-Flo Underlayments or Wear-Toppings.

Tenon^® Masonry Cement

Tenon® Masonry Cement is designed to be mixed with masonry sand to create masonry mortar for various applications such as brick and stone. Type N Masonry Cement (BOM #114094) is used for non-structural, above-grade applications such as setting brick or stone veneer and comes in a 70 lb. bag. Type S Masonry Cement (BOM #114095) is designed for structural above-grade or below-grade application and comes in a 75 lb. bag. Type M Masonry Cement (BOM #114096) is used for structural, below-grade, load-bearing walls where higher compressive strengths are needed and comes in a 70 lb. bag.

Tenon^® Masonry Veneer Joint Grout

Tenon® Masonry Veneer Joint Grout is blend of dry, cementitious materials, performance admixtures, and dried sand specifically designed to fill or tuck-point the joints between artificial stone, brick, masonry, and natural stone in veneer systems. Preblended with air-entrainment admixtures to resist freeze-thaw conditions, while increasing flow and durability. Tenon Pro Veneer Technology (PVT) creates a high-performance professional grout, formulated for clean installation and flow properties to eliminate clogging when using a grout bag. Available in: Natural Gray (BOM #120463); White (BOM #120464); Tan (BOM #120465); and Brown (BOM #120466).

Tenon^® Masonry Veneer Mortar HB

Tenon® Masonry Veneer Mortar HB (High Bond) (BOM #120462) is a high-performance, non-sag, fiber-reinforced, polymer-modified bonding mortar for installing real or manufactured masonry veneer units. Our Pro Veneer Technology (PVT) is a blend of cementitious materials, oven-dried sand, and special performance admixtures to create a professional strength mortar. This high-yield mortar allows for the same coverage as a traditional 50 lb. bag in a lighter-weight 40 lb. size. Meets or exceeds the requirements of ANSI A118.4, A118.11, A118.15 and ASTM C270.

Tenon^® Masonry Veneer Mortar PM

Tenon® Masonry Veneer Mortar PM (Polymer-Modified) (BOM #120461) is a high-performance, multi-purpose, polymer-modified mortar, used for both traditional thick bed scratch and base coats and as the bonding mortar for installing real or manufactured masonry veneer units. A blend of cementitious materials, oven-dried sand, and special performance admixtures, our Pro Veneer Technology (PVT) creates both a mechanical and chemical bond to the substrate, significantly outperforming standard Type S and N mortars. Can also be used for grouting, yet is excellent for applications such as dry stack where mortar joints are not used. Meets the requirements of ASTM C 1714, ASTM C270, ANSI 118.4, and ACI 530 Shear Bond Standards.

Tenon^® Metro Mix^™

Tenon® Metro Mix™ (BOM #128260) is a high performance concrete mix engineered to meet commercial/industrial ready mix specifications. Super plasticized for higher slump and compressive strengths with corrosion inhibitors. Ideal for projects requiring small structural concrete applications or when ready mix truck access is restricted. Use for structural applications and full depth repairs of 2" (51 mm) or greater. Exceeds ASTM C 387.

Tenon^® Metro Mix AE

Tenon® Metro Mix AE (BOM #128270) is the air-entrained version of our high performance concrete mix engineered to meet commercial/industrial ready mix specifications. Super plasticized for higher slump and compressive strengths with corrosion inhibitors. Ideal for projects requiring small structural concrete applications or when ready mix truck access is restricted. Use for structural applications and full depth repairs of 1½" (51 mm) or greater. Exceeds ASTM C 387.

Tenon^® Mighty Bond^™

Tenon® Mighty Bond™ is a high-solids, acrylic, liquid bonding agent that substantially improves adhesion, impact, and shear bond, tensile, and flexural and compressive strength of unmodified concrete, mortars, patches and grouts. Additionally, Mighty Bond adds excellent freeze/thaw and salt resistance and creates more durable cement-based materials. Minimal preparation is required. Available in 1 gal. bottles (BOM #120525), 5 gal. pails (BOM #120526) and 55 gal. drums (BOM #130020).

Tenon^® Partial Depth Concrete Patch

Tenon® Partial Depth Concrete Patch is is ideal for placing overlays less than 2” deep (5 cm). This pre-blended cement and oven dried sand mixture will produce a high-strength concrete repair material that is extremely durable in partial depth applications such as concrete pavements, bridge decks, industrial floors, concrete parking lots and garage decks. It is also used for adhering pavers to concrete steps and walks, patching and/or leveling concrete surfaces, filling large cracks, and filling cores in masonry block or brick. Available in 2:1 mix (BOM #120722), 2.5:1 mix (BOM #120723), or 3:1 mix (BOM #120724) (fine sand aggregate to Portland cement ratio).

Tenon^® Paver Guardian

Tenon® Paver Guardian is designed to protect & extend the life of installed pavers without changing the finished look. Paver Guardian provides a natural finish that maintains  the original look of pavers, concrete, architectural concrete, brick, natural stone, and other cementitious materials. This clear, solvent-based formula penetrates and reacts chemically within the capillaries of the concrete to protect against moisture  penetration, spalling, freeze-thaw damage, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Paver Guardian is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129670), 5 gal. pail (BOM #129660), or 55 gal. drum (BOM #129534).

Tenon^® Paver Guardian WB

Tenon® Paver Guardian WB is designed to protect & extend the life of installed pavers, retaining walls and other cementitious surfaces without affecting the finished look. Paver Guardian WB provides a natural finish that maintains the original look of pavers, concrete, architectural concrete, brick, natural stone, and other cementitious materials. This clear, water-bourne formula penetrates and reacts chemically within the capillaries of the surface to protect against deicing salts, moisture penetration, spalling, freeze-thaw damage,  efflorescence, and chemical erosion. Paver Guardian WB also protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Paver Guardian WB is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129780), 5 gal. pail (BOM #129790), or 55 gal. drum (BOM #129576).

Tenon^® Paver Seal

Tenon® Paver Seal is designed to protect & extend the life of installed pavers, while enhancing the color and adding a matte finish. Made with a blend of methacrylate polymers, this solvent -based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on concrete, architectural concrete, brick, natural tile, and other cementitious materials. Paver Seal will enhance the beauty of pavers, colored or stamped concrete, or exposed aggregate yet keep a matte finish. It forms a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129730), 5 gal. pail (BOM #129720), or 55 gal. drum (BOM #129551).

Tenon^® Paver Seal Pro WB

Tenon® Paver Seal Pro WB is a penetrating, breathable, waterborne sealer designed to protect & extend the life of installed pavers, while enhancing the color with a natural, non-gloss finish. Made with a durable polysiloxane that does not yellow when exposed to the sun's UV rays, it penetrates deep in the capillaries of the paving stones for increased protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion. Paver Seal Pro WB will enhance the beauty of pavers, stone veneer, and architectural concrete by making colors more vibrant while protecting surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants and making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129770), 5 gal. pail (BOM #129760), or 55 gal. drum (BOM #129563).

Tenon^® Paver Seal & Shine

Tenon® Paver Seal & Shine is designed to protect & extend the life of installed pavers, while enhancing color and adding a gloss finish. Made with a blend of methacrylate polymers, this solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on concrete, architectural concrete, brick, natural stone, and other cementitious materials. Paver Seal & Shine will enhance the beauty of pavers, colored or stamped concrete, or exposed aggregate by giving it a rich “wet-look” gloss. It provides a membrane to increase protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these  surfaces easier to clean. Available in 1 gal. bottle (BOM #129690), 5 gal. pail (BOM #129680), or 55 gal. drum (BOM #129539).

Tenon^® Paver Seal & Shine Pro WB

Tenon® Paver Seal & Shine Pro WB is a penetrating, breathable, waterborne sealer designed to protect & extend the life of installed pavers, while enhancing the color and adding a “wet-look” gloss. Made with a durable acrylic that does not yellow when exposed to the sun's UV rays, it penetrates deep in the capillaries of the paving stones for increased protection from damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion. Paver Seal & Shine Pro WB will enhance the beauty of pavers, colored or stamped concrete, or exposed aggregate by giving it a “wet-look” finish while protecting surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants and making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129710), 5 gal. pail (BOM #129700), or 55 gal. drum (BOM #129545). 

Tenon^® Paver Seal Ultra Shine

Tenon® Paver Seal Ultra Shine is a high-solids, low-viscosity, sprayable sealing agent designed to protect & extend the life of installed pavers, while enhancing color and adding a high-gloss “wet look” finish. Made with a blend of 100% methacrylate polymers, this solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on architectural concrete, brick, natural stone, and other cementitious materials. Paver Seal Ultra Shine will enhance the beauty and vibrancy of colored or stamped concrete and exposed aggregate giving it a rich high-gloss finish. It forms a membrane to increase protection from  damaging freeze-thaw cycles, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, oil, grease, foods, and airborne pollutants while making these surfaces easier to clean. Available in 1 gal. bottle (BOM #129750), 5 gal. pail (BOM #129740), or 55 gal. drum (BOM #129556).

Tenon^® Paver Wash

Tenon® Paver Wash is a mild, phosphoric product that dissolves and removes efflorescence (white mineral deposits) and rust stains from pavers and other cementitious or clay surfaces. This product is recommended to be used before applying a sealer to the surface of pavers in order to enables the sealer to penetrate and seal more effectively. Available in 1 gal. bottle (BOM #129800) or 5 gal. pail (BOM #129810).

Tenon^® Pourable Concrete Patch

Tenon® Pourable Concrete Patch (BOM #120672) is a Portland cement-based, flowable, squeegee-grade, polymer-modified patching and resurfacing mix for interior and exterior horizontal concrete substrates. Easy to use, it corrects defects up to ½ in. (13 mm) on concrete surfaces prior to applying new flooring materials or coatings. Depending on application, can also be used as a wearable surface for residential and light duty commercial applications. Meets ASTM C387 “Standard Specification for Packaged, Dry, Combined Materials for Mortar and Concrete” for normal weight concrete.

Tenon^® Rapid Patch^® 100

Tenon® Rapid Patch® 100 (BOM #120970) is a fast-setting, fiber-reinforced, high strength, cement-based repair mortar designed for applications where high early strength gain is needed to reduce down time. Apply neat from 1/2" to 2" deep, can be extended for repairs greater than 2" deep. 

Tenon^® Rapid Patch^® 200

Tenon® Rapid Patch® 200 (BOM #120971) is a rapid-setting, fiber reinforced, high strength, polymer-modified cement mortar designed for concrete repair and overlay applications requiring high durability. Apply neat from 1/2" to 2" deep, or can be extended for repairs greater than 2" deep. Wide temperature range for application.

Tenon^® Rapid Strength Concrete Mix SE

Tenon® Rapid Strength Concrete Mix SE (BOM #120965) is a commercial grade blend of fast-setting cement, sand, gravel, and other proprietary performance additives designed to provide extended working time and high early strength for concrete applications requiring a minimum thickness of 1.5 in. (38 mm). Air-entrained for improved workability and freeze-thaw resistance, this mix is performance enhanced with corrosion inhibitors and contains fibers for crack resistance and increased toughness.

Tenon^® Rapid Strength Construction Grout LT

Tenon® Rapid Strength Construction Grout LT is a uniquely formulated non-corrosive, cementitious, flowable construction grout. It is designed for extreme duty applications where early strength, fast setting strengths at low temperatures are required.

Tenon^® Refractory Mortar

Tenon® Refractory Mortar is a specially-engineered blend of specific cements and aggregates giving the mortar unique heat-resistance and thermal characteristics for use in high-temperature applications such as inside fire pit rings, setting chimney clay flue liners, parging a smoke chimney chamber, and setting fire bricks. Passes ASTM C 199 for mortar temperature limits to 2,550°F for a minimum of 6 hours. 

Tenon^® Restoration Cleaner

Tenon® Restoration Cleaner is a phosphoric acid product that dissolves and removes efflorescence (white mineral deposits) and rust stains from concrete surfaces, masonry units, pavers, brick, etc. This product is recommended to be used before applying a sealer to the surface of concrete or masonry, this enables the sealer to penetrate and seal more effectively. Masonry Restoration Cleaner may be used to prepare the surface of concrete or masonry prior to using Tenon® repair products.

Tenon^® Rub-Pro^™

Tenon® Rub-Pro is a one-component, polymer-modified, Portland cement-based, interior and exterior resurfacer designed for smoothing and filling vertical and overhead concrete and masonry surfaces. Available in #3 light gray bag (BOM #128180) and light gray pail (BOM# 121153).

Tenon^® Salt Barrier

Tenon® Salt Barrier is designed to protect & extend the life of concrete, masonry, pavers, retaining walls and other cementitious surfaces by protecting from the damaging effects of salt and de-icing chemicals without affecting the finished look. Salt Barrier provides a natural finish that maintains the original appearance of driveways, patios, garage floors, block walls, and other concrete or masonry surfaces. This clear, solvent-based formula penetrates and reacts chemically within the capillaries of the concrete. This product protects against moisture  penetration, spalling, freeze-thaw damage, deicing salts, efflorescence, and chemical erosion. It also protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making those surfaces easier to clean. Salt Barrier is used for above-grade exterior applications that are not subject to hydrostatic pressure.

Tenon^® Salt Barrier ES

Tenon® Salt Barrier ES (Exempt Solvent) is designed to protect & extend the life of concrete, masonry, pavers, retaining walls and other cementitious surfaces by protecting from the damaging effects of salt and de-icing chemicals without affecting the finished look. Salt Barrier ES provides a natural finish that maintains the original appearance of driveways, patios, garage floors, block walls, and other concrete or masonry surface. This clear, solvent-based formula penetrates and reacts chemically within the capillaries of the concrete to protect against moisture penetration, spalling, freeze-thaw damage, deicing salts, efflorescence, and chemical erosion, protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Salt Barrier ES is used for above-grade exterior applications that are not subject to hydrostatic pressure.

Tenon^® Salt Barrier WB

Tenon® Salt Barrier WB is designed to protect & extend the life of concrete, masonry, pavers, retaining walls and other cementitious surfaces by protecting from the damaging effects of salt and de-icing chemicals without affecting the finished look. Salt Barrier WB provides a natural finish that maintains the original appearance of driveways, patios, garage floors, block walls, and other concrete or masonry surfaces. This clear, water -based formula penetrates and reacts chemically within the capillaries of the surface to protect against deicing salts, moisture penetration, spalling, freeze-thaw damage, efflorescence, and chemical erosion. Salt Barrier WB also protects surfaces from most chemicals, dirt, acids, alkali, and airborne pollutants while making these surfaces easier to clean. Salt Barrier WB is used for above-grade exterior applications that are not subject to hydrostatic pressure. Available in 1 gal. bottle (BOM #129840), 5 gal. pail (BOM #129580), or 55 gal. drum (BOM #129587).

Tenon^® Self-Consolidating Concrete Mix CI

Tenon® Self-Consolidating Concrete Mix (SCC) CI (BOM #112026) is a dry, preblended, one-component, self consolidating, cementitious, polymer-modified concrete mix containing coarse aggregate, silica fume, and an integral migrating corrosion inhibitor. Designed for application thickness minimum of 1 in. (2.5 cm) and maximum thickness of 8 in. (20 cm). Also available with integral water repellent (IWR) Tenon Self-Consolidating Concrete Mix (SCC) CI/IWR (BOM 114393).

Tenon^® Self-Leveling Resurfacer

Tenon® Self-Leveling Resurfacer (BOM #121017) is a polymer-modified, cement-based product for resurfacing concrete floors with damaged finishes or as a wear surface for light industrial floors where a hard, flat smooth surface and a quick return to service is desired. Also use as an underlayment for installation of ceramic tile, stone, resilient flooring, carpet, or other finished flooring. Typical substrates include: fully cured concrete, APA rated exterior grade/exposure 1 plywood or OSB underlayment grade equivalent with expanded wire lath reinforcement. Install from feather edge to 1 in. (25 mm) thick.

Tenon^® Set Accelerator

Tenon® Set Accelerator (BOM #120376) is an ASTM C494, Type C, non-chloride, non-corrosive, liquid that improves workability and initial strength while it reduces the hydration time of cement.  The product is recommended for use during cooler weather to accelerate set time and reduce the risk of frozen mortar and concrete mixes. It is also recommended for use when early strength gain is desired to speed up projects. Tenon Set Accelerator provides a reduced curing time, faster set time and increased early strength. The product speeds finishing operations in any weather condition without any corrosive effects.

Tenon^® Set Retarder

Tenon® Set Retarder is a ready-to-use liquid admixture that slows the rate of reaction for rapid setting concrete repair products, including:

• Tenon® Commercial DOT Repair
• Tenon® Rapid Patch 100
• Tenon® Rapid Patch 200
• Tenon® Vertical Repair CI
• Tenon® Rapid Strength Concrete Mix SE
• Tenon® Blend-Pro
• Rapid Patch® Multi-Purpose Repair
• Rapid Patch® Concrete Repair Mortar

It is intended for use with these products in conditions where warm weather or other situations require extended working time for proper placement and finishing. It meets ASTM C494/C 494M requirements for Type B retarding admixtures. For use with all other mixes contact info@tccmaterials.com to connect with a technical representative.

Tenon^® Shotcrete D-LR Microfiber

Tenon® D-LR1 Microfiber is a dry-process shotcrete containing a pre-blended Portland cement, air-entraining admixture, set time accelerator, synthetic fibers, selectively blended aggregates, and propriety performance enhancing components. Available in 80 lb. bags (BOM #112865) and 3000 lb. bags (BOM #110258). Tenon® D-LR2 Microfiber is specifically designed to provide low resistivity values complimenting preplaced cathodic protection systems. Available in 80 lb. bags (BOM #112866) and 3000 lb. bags (BOM #112864).

Tenon^® Shotcrete D-SF Microfiber

Tenon® D-SF Microfiber is a dry process shotcrete containing a pre-blended Portland cement, silica fume, air-entraining admixture, set time accelerator, synthetic fibers, selectively blended aggregates, and propriety performance enhancing components. Tenon® D-SF Microfiber is specifically designed to provide excellent application characteristics with balanced performance properties. This product is approved by MNDOT for "Shotcrete - Concrete Surface Repairs". Available in 80 lb. bags (BOM #112870 & BOM #112868) and 3000 lb. bags (BOM #112869 & BOM #112867).

Tenon^® Siloxane Final Seal

Tenon® Siloxane Final Seal is an aromatic, solvent-based concrete sealer/water-repellant used to protect cementitious surfaces against the damage caused by water penetration. Can be applied to surfaces where a cure and seal coating was previously applied. Available in 1 gal. bottle (BOM #120828), 5 gal. pail (BOM #120827), and 55 gal. drum (BOM #120829).

Tenon^® Siloxane Sealer

Tenon® Siloxane Sealer is a clear, solvent-based sealer for concrete and cementitious materials. It penetrates and reacts chemically within the capillaries to repel water and protect from the damaging effects of rain, water penetration, chemicals, salt, freeze-thaw cycles, and smog. Provides natural-looking, non-yellowing, invisible protection.  Available in 1 gal. bottle (BOM #120826), 5 gal. pail (BOM #120825), and 55 gal. drum (BOM #120829).

Tenon^® Super Clear Coat

Tenon® Super Clear Coat is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic solvent-based coating does not yellow when exposed to the sun’s UV rays and can also be used as a final sealer on burnish block, architectural concrete, brick, slate, paving stone, terrazzo, quarry tile, and cementitious materials. Enhances the colors of the surfaces with a rich "wet-look" sheen. Available in 1 gal. bottle (BOM #120831), 5 gal. pail (BOM #120830), and 55 gal. drum (BOM #120832).

Tenon^® Super Clear Coat Matte

Tenon® Super Clear Coat Matte is used for curing and sealing exposed aggregate and sealing colored concrete. This aromatic, solvent-based sealer does not yellow under the sun's UV rays. It enhances the beauty of colored or stamped concrete and exposed aggregate yet keeps a matte, low gloss finish. Available in 1 gal. bottle (BOM #120834), and 5 gal. pail (BOM #120833).

Tenon^® Super Diamond Glaze

Tenon® Super Diamond Glaze is a higher viscosity version of Super Clear Coat used for curing and sealing exposed aggregate and sealing colored concrete. Enhances the beauty and depth of the surface, giving it a rich "wet-look" high gloss while protecting from the damages caused by moisture penetration. Available in 1 gal. bottle (BOM #120836), 5 gal. pail (BOM #120835), and 55 gal. drum (BOM #120837).

Tenon^® SuperFlow

Tenon® SuperFlow water-reducing admixture is a full range water reducing additive providing a more plastic and flowable concrete. It produces concrete mixes with different levels of workability to include self-consolidating concrete (SCC) applications. Tenon SuperFlow admixture meets ASTM C494-C 494M compliance requirements for Type A water-reducing and Type F high-range water-reducing admixtures.

Tenon^® Surface Bonding Cement CR

Tenon® Surface Bonding Cement CR is a versatile fiber-reinforced, Portland cement-based product used to build and restore retaining walls or block walls, patch large vertical holes where non-sagging cement is a must, repair deteriorated stucco, and in the construction of concrete block walls that are dry stacked (without mortar) above the first course. Special fibers control shrinkage, cracking, and sagging on vertical applications and provides additional overall strength when compared with conventional concrete. Available in Gray (BOM #113951) and White (BOM #113952).

Tenon^® Surface Renew

Tenon® Surface Renew is a clear cleaning solution to revitalize and rejuvenate aged, sealed concrete.  

Tenon^® Thermaseal^® Geothermal Grout

Tenon® Thermaseal^® Geothermal Grout is a a thermally-conductive cementitious grout engineered for application of vertical and horizontal ground source heat pumps and geothermal well fields. Non-toxic and non-shrink with a high solids content and a low-permeability factor making it ideal for ground source heat loops and safe for contact with potable ground water. A blend of thermally-conductive sand with Portland cement for a range of thermal conductivities depending on design requirements. Thermaseal Geothermal Grout also offers low-absorption with a rigid seal to prevent integration of aquifers and is made in three versions, MN Mix (BOM #121014), and 0.75 HF (high-flow) (BOM 129569).

Tenon^® Tile Crete^® Floor Mud

Tenon® Tile Crete® Floor Mud Underlayment Mix is a blend of cementitious material and oven-dried sand designed to produce a highly-bondable substrate and to optimize consistency between batches. Use as a setting bed/underlayment for ceramic, mosaic, stone, quarry, and paver tile over concrete or wood substrates including countertops. Ideal for forming shower pans and curbs as well as installations requiring a slope to drain.

Tenon^® Tile Crete^® Floor Mud PM

Tenon® Tile Crete® PM Floor Mud Underlayment Mix is a blend of cementitious material, oven-dried sand and special polymers designed to produce a highly bondable substrate and to optimize consistency between batches. Integral polymer eliminates the need for adding a liquid polymer during mixing when polymer is desired for freeze-thaw durability and enhanced bond. Use as a setting bed/underlayment for ceramic, mosaic, stone, quarry, and paver tile over concrete or wood substrates including countertops. Ideal for forming shower pans and curbs as well as installations requiring a slope to drain. Interior Applications: Tile Crete® PM Floor Mud Underlayment Mix (BOM #110473), Fast-Set Tile Crete® PM Floor Mud (BOM #112521) Exterior Applications: Tile Crete® PM Exterior Floor Mud Underlayment Mix (BOM #112323)

Tenon^® TraxGrip

Tenon® TraxGrip gives a light texture to concrete flatwork for a slip-resistant surface. Often used commercially on entrance floors, garage floors, steps, patios, walkways, and any surface where additional texture is desired to increase non-slip characteristics. TraxGrip is an optically clear thermoset polymer resin. Nearly invisible on the applied floor surface, it is added to curing and sealing compounds then applied to surfaces in the liquid solution. Available in 3.2 oz (BOM #114637) and 1 lb. (BOM #114638)

Tenon^® Trowel Ice

Tenon® Trowel Ice is a V.O.C. compliant finishing aid that enhances physical concrete surface performance, while aiding in faster and easier surface finishing. Tenon® Trowel Ice is reactive colloidal silicate densifier that lubricates freshly placed concrete, prolonging workability in adverse conditions, such as high wind, low humidity, or high ambient temperatures. Available in 1 gal. Ready-to-Use bottle (BOM #114864), 5 gal. Ready-to-Use pail (BOM #114866), 1 gal. Concentrated bottle (BOM #114865) and 5 gal. Concentrated pail (BOM #114867).

Tenon^® Ultimate Barrier

Tenon® Ultimate Barrier is a clear, non-yellowing, fast drying acrylic-silicone blended concrete sealer for curing, dustproofing, and weatherproofing of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials. Tenon® Ultimate Barrier is designed to be a single application for curing, sealing, and weatherproofing. Tenon® Ultimate Barrier forms a membrane film on new concrete to seal and retain hydration water, providing optimum curing of the substrate, resistance to abrasion, damage caused by salt, oil, grease, mild acids, alkali, and stains from soot, smog, fumes, and gases. Tenon® Ultimate Barrier reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to cure, protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials.

Tenon^® Ultimate Barrier ES

Tenon® Ultimate Barrier ES is a VOC compliant, clear, non-yellowing, fast drying acrylic-silicone blended concrete sealer for curing, dustproofing, and weatherproofing of freshly-placed and/or existing concrete, terrazzo, brick, stone, architectural concrete, and other cementitious materials.

Tenon Ultimate Barrier ES is designed to be a single application for curing, sealing, and weatherproofing. Tenon® Ultimate Barrier ES forms a membrane film on new concrete to seal and retain hydration water, providing optimum curing of the substrate, resistance to abrasion, damage caused by salt, oil, grease, mild acids, alkali, and stains from soot, smog, fumes, and gases.

Tenon Ultimate Barrier ES reacts chemically within the capillaries of the concrete or masonry to protect against moisture penetration and the spalling, freeze damage, and rebar corrosion which moisture can cause. It is suitable for use to cure, protect, and seal fully-cured, new concrete, existing concrete, stucco, architectural concrete, and other cementitious materials.

Tenon^® Ultra High Strength Precision Grout

Tenon®Ultra High Strength Precision Grout is a uniquely formulated cementitious, flowable precision grout.  It is designed for extreme duty applications where high early strength and extremely high finish strengths are required. Available in 50 lb. bag (BOM #114200).

Tenon^® Underground Utility Mortar

Tenon® Underground Utility Mortar 50 lb. (BOM #120704) and 80 lb. (BOM #114181) is a is a dry, preblended, air-entrained mortar mix containing Portland cement, hydrated lime, and dried masonry sand formulated for superior bond and outstanding freeze-thaw resistance in all underground precast concrete structure applications. This product meets ASTM C270 and ASTM C1714 requirements.

Tenon^® Vertical Concrete Surface Finisher

Tenon® Vertical Concrete Surface Finisher is a superior cementitious waterproofing coating for concrete and masonry. It provides a protective and waterproof surface while eliminating the rubbing process. Spray or brush applied, available in light gray (BOM #120765) or white (BOM #120764). For added performance, durability, and improved bonding, Vertical Concrete Surface Finisher is designed to be mixed with Tenon Mighty Bond liquid additive. Vertical Concrete Surface Finisher when mixed with Mighty Bond is approved by MNDOT under Special Surface Finish System.

Tenon^® Vertical Repair CI

Tenon® Vertical Repair CI (BOM# 113810) is a polymer modified, high-strength, fast-setting, non-shrink, patching material for commercial and industrial vertical and overhead holes in concrete or masonry. Can be shaved or molded to required shapes.

Note: Also available without corrosion inhibitor (BOM# 126171).

Tenon^® Vinyl Concrete Patch

Tenon® Vinyl Concrete Patch a polymer-modified, Portland cement-based patching compound used to repair minor surface imperfections in concrete. Suitable for interior and exterior applications from feather-edge to 2 in. (51 mm) thick per lift. Typically supports foot traffic in 8-12 hours, wheeled traffic in 48 hours. Available in 10 lb. pail (BOM #127634) and 50 lb. bag  (BOM #120681). 

Tenon^® Waterproofing & Crack Isolation Membrane

Tenon® Waterproofing & Crack Isolation Membrane is an advanced latex polymer-based technology used as a professional grade waterproofing underlayment membrane or as part of a crack isolation system. Salmon color when applied, dries to dark orange. Available in 1 gal. pail (BOM #120675) and 5 gal. (BOM #120676).

Tenon^® Wax Cure 1315 WB

Tenon® Wax Cure 1315 WB is a water-based, white pigmented, liquid membrane forming, wax curing compound used for moisture retention of freshly placed concrete. Tenon® Wax Cure 1315 WB is formulated for curing concrete. The addition of white pigment to the wax film reflects the heat of the sun to protect excess heat build-up. Designed for exterior applications, it is particularly recommended for roadways, airport runways, parking lots, and other pavement projects where greater moisture retention is required . Tenon® Wax Cure 1315 WB will pass all VOC compliance laws. Available in 5 gallon pails (BOM #113830), 55 gallon drums (BOM #113829), and 275 gallon totes (BOM #113828).

Tenon^® Wax Cure 309 WB

Tenon® Wax Cure 309 WB is a water-based, white pigmented, liquid membrane forming, wax curing compound used for moisture retention of freshly placed concrete. Tenon® Wax Cure 309 WB is formulated for curing concrete. The addition of white pigment to the wax film reflects the heat of the sun to protect excess heat build-up. Designed for exterior applications, it is particularly recommended for slip form , curb and gutter, and municipal sidewalk applications where minimum moisture retention is required. Tenon® Wax Cure 309 WB will pass all VOC compliance laws. Available in 50 lb. pails (BOM #113860), 55 gallon drums (BOM #113849), and 275 gallon totes (BOM #113851).

Tenon^® X-Tender

Tenon^® X-TENDER is a V.O.C. compliant concentrate, mixed 1 part concentrate to 9 parts water that creates a sprayable monomolecular polymer film when properly sprayed to freshly placed concrete.  Tenon^® X-TENDER is specifically designed to minimize rapid moisture loss from concrete surfaces prior to curing. Available in a 1 gallon bottle (BOM# 114871) and 5 gallon pail (BOM# 114872).  

Tenon^® Xylene

Tenon® Xylene is a cleaning solvent for cleaning tools, sprayers, and equipment used in concrete and masonry construction. Tenon Xylene may also be used to soften previously applied acrylic sealers.